What Are The Characteristics, Main Alloying Elements And Functions Of 3xxx Aluminum Alloys?

Aug 08, 2024

Leave a message

(1) Characteristics of 3xxx aluminum alloys

3xxx aluminum alloys are aluminum alloys with manganese as the main alloying element and are non-strengthening aluminum alloys by heat treatment. They have high plasticity, good welding performance, and higher strength than 1xxx aluminum alloys. Their corrosion resistance is similar to that of 1xxx aluminum alloys. They are medium-strength aluminum alloys with good corrosion resistance. They are widely used and used in large quantities.

 

(2) The role of alloying elements and impurity elements in 3XXX series aluminum alloys

Mn: Mn is the only main alloying element in 3XXX series Al alloys. Its content is generally in the range of 1.0%~1.6%. The strength, plasticity and processing properties of the alloy are good. Mn and Al can form MnAl6 phase. The strength of the alloy increases with the increase of Mn content. When the Mn content is higher than 1.6%, the strength of the alloy increases accordingly. However, due to the formation of a large amount of brittle compounds MnAls, the alloy is prone to cracking when deformed. With the increase of Mn content, the recrystallization temperature of the alloy increases accordingly. Since this series of alloys has a large supercooling ability, it produces a large intragranular segregation during rapid cooling and crystallization. The concentration of Mn is low in the center of the dendrite and high at the edge. When there is obvious Mn segregation in the cold-worked product, coarse grains are easily formed after annealing.

 

ACP-alloy3003

 

ACM-aluminium composite panel alloy3003

 

 

Fe: Fe can dissolve in MnAl6 to form (FeMn)Als compounds, thereby reducing the solubility of Mn in Al. Adding 0.4% to 0.7% Fe to the alloy, but ensuring that Fe+Mn is no more than 1.85%, can effectively refine the grains of the plate after annealing. Otherwise, a large number of coarse flaky (FeMn) Al6 compounds will be formed, which will Significantly reduce the mechanical properties and process properties of the alloy.

 

Si: Si is a harmful impurity. Si and Mn form a complex ternary phase T (Al12Mn3Si2) phase, which can also dissolve Fe to form (Al, Fe, Mn, SiD quaternary phase. If Fe and Si exist at the same time in the alloy, a (Al2 Fe3Si2 ) or β(AlgFe2Si2) phase, destroying the beneficial influence of Fe. Therefore, Si in the alloy should be controlled below 0.6%. Si can also reduce the solubility of Mn in Al, and has a greater impact than Fe and Si. The decomposition process of Mn from the supersaturated solid solution during thermal deformation can also improve some mechanical properties.

 

Mg: A small amount of Mg (≈0.3%) can significantly refine the annealed grains of this alloy and slightly increase its tensile strength. But it also damages the surface gloss of the annealed material. Mg can also be an alloying element in Al-Mg alloy. Adding 0.3% to 1.3% Mg increases the strength of the alloy and reduces the elongation (annealed state), so the AI-Mg-Mn alloy is developed.

 

Cu: The alloy contains 0.05%~0.5% Cu, which can significantly improve its tensile strength. However, containing a small amount of Cu (0.1%) can reduce the corrosion resistance of the alloy, so the Cu content in the alloy should be controlled below 0.2%. To ensure the welding performance of the alloy, the Zn content is limited to less than 0.2%.

 

Zn: When the Zn content is less than 0.5%, it has no significant impact on the mechanical properties and corrosion resistance of the alloy. Considering the welding performance of the alloy, the Zn content is limited to less than 0.2%. 

 

aluminium-honeycomb-panel

 

What are the types and uses of 3xxx series aluminum alloys?

 

Alloy 3003

Varieties: Plates, thick plates, drawn tubes, extruded tubes, profiles, bars, wires, cold-worked bars, cold-worked wires, rivet wires, forgings, foils, heat sink blanks

Uses: Used for processing parts that require good forming properties, high corrosion resistance or good weldability, or workpieces that require these properties and require higher strength than 1XXX series alloys, such as tanks and tanks for transporting liquid products, pressure tanks, storage devices, heat exchangers, chemical equipment, aircraft fuel tanks, oil pipes, reflectors, kitchen equipment, washing machine cylinders, rivets, welding wires

 

Alloy 3004

Varieties: Plates, thick plates, drawn pipes, extruded various lighting parts production and storage devices, thin plate processing parts, building baffles, cable ducts, sewer pipes,

Uses: All-aluminum can bodies, parts requiring higher strength than 3003 alloy, chemical product production and storage devices, thin plate processing parts, building baffles, cable ducts, sewer pipes, various lighting parts

 

Alloy 3105

Varieties: Plates

Uses: Room partitions, baffles, movable house panels, gutters and downpipes, thin plate forming parts, bottle caps, etc.

 

Alloy3003-Aluminum-Coil

 

alloy3003-aluminum-coating-coil